This lovely charm bracelet features PRESTIGE Crystal beads and TierraCast charms. It is filled with an array of beautiful PRESTIGE bicones dangling off a pretty cold chain. Please note that the finish of the charms has been changed from those pictured. They are now a lovely assortment of a variety of finished to add an eclectic look to this design.
You can follow the photo to decorate your bracelet with charms and dangles or place them wherever you wish along the chain. Please cut your chain to your desired wrist size before adding the adornments. Start by cutting your chain to your desired bracelet size, please note that the clasp will add about 1/2 an inch to the overall length.
Using a 5mm jump ring, connect your lobster clasp to one side of your bracelet. The other side you will simply connect the lobster clasp to the end chain link.
To create all your dangles, you have two choices. First, place the desired beads/charms onto a head pin and create a simple wire loop after the last bead. The second choice is to snip the head off a head pin, make a very small little loop on the end for a decorative touch, and then place your beads onto this new type of head pin. Again, create a simple wire loop after the last bead and trim off excess wire.
Please refer to the photo and make your dangles accordingly. For most of the charms, the pattern is: 4mm bicone bead, charm, 4mm bicone bead. Some charms have two bicones on each side of the charm.
For the little bead clusters, the pattern is head pin with loop with two bicones on it and then another head pin with loop with one matching bicone on it. Both these dangles are connected to a 5mm jump ring which is then connected to the bracelet.
To make the dragonfly charm, use 1 head pin with the following beads put on it: 3mm bicone in golden topaz , 4mm bicone in peridot, 3mm golden topaz bicone, 4mm peridot bicone, 3mm golden topaz bicone, gold dragonfly wings, 4mm golden topaz bicone. Create a simple wire loop after the last bead. Also bend the "tail" a little to make it look more dynamic. Now connect this to roughly the center chain link of your bracelet using a 4mm jump ring.
Have fun creating your charms and dangles and placing them along your bracelet chain!
Nice choice! All or most of the products needed for this project are shown below with quantities. Sometimes we sell out of components and aren’t able to order more from the manufacturer (we know, it is very disappointing to us, too). Use the opportunity to mix up the design and make it yours by substituting similar products or altering the entire color scheme—it’s up to you!
Create a spring bracelet with a variety of charms and crystals.
This lovely charm bracelet features PRESTIGE Crystal beads and TierraCast charms. It is filled with an array of beautiful PRESTIGE bicones dangling off a pretty cold chain. Please note that the finish of the charms has been changed from those pictured. They are now a lovely assortment of a variety of finished to add an eclectic look to this design.
You can follow the photo to decorate your bracelet with charms and dangles or place them wherever you wish along the chain. Please cut your chain to your desired wrist size before adding the adornments. Start by cutting your chain to your desired bracelet size, please note that the clasp will add about 1/2 an inch to the overall length.
Using a 5mm jump ring, connect your lobster clasp to one side of your bracelet. The other side you will simply connect the lobster clasp to the end chain link.
To create all your dangles, you have two choices. First, place the desired beads/charms onto a head pin and create a simple wire loop after the last bead. The second choice is to snip the head off a head pin, make a very small little loop on the end for a decorative touch, and then place your beads onto this new type of head pin. Again, create a simple wire loop after the last bead and trim off excess wire.
Please refer to the photo and make your dangles accordingly. For most of the charms, the pattern is: 4mm bicone bead, charm, 4mm bicone bead. Some charms have two bicones on each side of the charm.
For the little bead clusters, the pattern is head pin with loop with two bicones on it and then another head pin with loop with one matching bicone on it. Both these dangles are connected to a 5mm jump ring which is then connected to the bracelet.
To make the dragonfly charm, use 1 head pin with the following beads put on it: 3mm bicone in golden topaz , 4mm bicone in peridot, 3mm golden topaz bicone, 4mm peridot bicone, 3mm golden topaz bicone, gold dragonfly wings, 4mm golden topaz bicone. Create a simple wire loop after the last bead. Also bend the "tail" a little to make it look more dynamic. Now connect this to roughly the center chain link of your bracelet using a 4mm jump ring.
Have fun creating your charms and dangles and placing them along your bracelet chain!
Create a spring bracelet with a variety of charms and crystals.