Raven's Journey wild rose beads create a magical display in this beaded necklace. They dangle beautifully from the Anna Bronze focal branch.
For the earrings, slide a gold spacer onto a head pin, followed by a 6/0 Czech glass seed bead, a brass spacer, a Wild Rose bead, a brass spacer, a 6/0 seed bead, and a gold spacer. Make a wrapped loop at the top of the beads.
Open the loop of an earwire and attach to the wrapped loop. Close the loop.
Repeat these steps to make the other earring.
For the necklace, cut a length of jewelry wire approximately 11 inches. Slide a crimp tube onto the end, followed by a jump ring. Bring the wire back through the crimp tube and crimp in place. Hide the crimp with a crimp cover.
Opening and Closing Jump Rings Video
Crimp Tool Tutorial
Crimp Tube Video Tutorial
Crimp Cover Tutorial
Add a brass spacer, a 6/0 seed bead, and a gold spacer to the wire. Then, add 14 faceted round beads.
Add the following pattern to the wire:
Repeat this pattern two times.
Slide a crimp tube onto the end of the wire, followed by a jump ring attached to one side of the branch pendant. Bring the wire back through the crimp tube and crimp in place. Hide the crimp with a crimp cover.
Repeat steps 4-7 on the other side of the branch pendant. Attach each half of the clasp to each end of the necklace using a jump ring for each (so that each half of the clasp is attached to the ends of the necklace with two linked jump rings).
Add a wild rose bead to a head pin and make a simple loop at the top of the bead. Attach this dangle to the center loop on the branch pendant. Repeat this step three times, adding each flower dangle to a new loop on the branch pendant.
Nice choice! All or most of the products needed for this project are shown below with quantities. Sometimes we sell out of components and aren’t able to order more from the manufacturer (we know, it is very disappointing to us, too). Use the opportunity to mix up the design and make it yours by substituting similar products or altering the entire color scheme—it’s up to you!
Raven's Journey wild rose beads create a magical display in this beaded necklace. They dangle beautifully from the Anna Bronze focal branch.
For the earrings, slide a gold spacer onto a head pin, followed by a 6/0 Czech glass seed bead, a brass spacer, a Wild Rose bead, a brass spacer, a 6/0 seed bead, and a gold spacer. Make a wrapped loop at the top of the beads.
Open the loop of an earwire and attach to the wrapped loop. Close the loop.
Repeat these steps to make the other earring.
For the necklace, cut a length of jewelry wire approximately 11 inches. Slide a crimp tube onto the end, followed by a jump ring. Bring the wire back through the crimp tube and crimp in place. Hide the crimp with a crimp cover.
Opening and Closing Jump Rings Video
Crimp Tool Tutorial
Crimp Tube Video Tutorial
Crimp Cover Tutorial
Add a brass spacer, a 6/0 seed bead, and a gold spacer to the wire. Then, add 14 faceted round beads.
Add the following pattern to the wire:
Repeat this pattern two times.
Slide a crimp tube onto the end of the wire, followed by a jump ring attached to one side of the branch pendant. Bring the wire back through the crimp tube and crimp in place. Hide the crimp with a crimp cover.
Repeat steps 4-7 on the other side of the branch pendant. Attach each half of the clasp to each end of the necklace using a jump ring for each (so that each half of the clasp is attached to the ends of the necklace with two linked jump rings).
Add a wild rose bead to a head pin and make a simple loop at the top of the bead. Attach this dangle to the center loop on the branch pendant. Repeat this step three times, adding each flower dangle to a new loop on the branch pendant.