Get creative with Anna Bronze skulls in your jewelry designs!
Slide the black leather necklace through the top center hole of the Anna Bronze skull.
Cut two lengths of jewelry wire, each approximately 24 inches long. Slide one wire through the bottom loop of the skull. Slide the other wire through the two side loops of the skull. Center the wires through the loops, so there is an equal amount of wire coming out from each side of the skull.
Add the following pattern to one side of the bottom wire:
Repeat this pattern on the other side of the strand.
Add the following pattern to one side of the top wire:
Repeat this pattern on the other side of the strand.
Slide a pinch bail over the last beads of both strands on one side of the necklace. Pinch the bail closed over the strands. Repeat on the other side of the necklace.
Add the following pattern to the bottom strand:
Add a crimp tube to the wire and loop the wire back through the crimp tube, leaving the loop long enough to be covered by three crimp covers. Crimp in place. Repeat this step on the other side of the necklace.
Add the following pattern to the top strand:
Add a crimp tube to the wire and loop the wire back through the crimp tube, leaving the loop long enough to be covered by two crimp covers. Crimp in place. Repeat this step on the other side of the necklace.
Slide the loop on one end of the short strand through the leather necklace, twisting the strand once around the necklace. Slide the loop down to create a swag or swoop in the strand to your liking. Once in place, secure with two crimp covers around the leather and glue. Allow to dry. Repeat on the other side of the necklace.
Slide the loop on one end of the long strand through the leather necklace, twisting the strand once around the necklace. Slide the loop down to create a swag or swoop to your liking. Once in place, secure with three crimp covers around the leather and glue. Allow to dry. Repeat on the other side of the necklace.
Nice choice! All or most of the products needed for this project are shown below with quantities. Sometimes we sell out of components and aren’t able to order more from the manufacturer (we know, it is very disappointing to us, too). Use the opportunity to mix up the design and make it yours by substituting similar products or altering the entire color scheme—it’s up to you!
Get creative with Anna Bronze skulls in your jewelry designs!
Slide the black leather necklace through the top center hole of the Anna Bronze skull.
Cut two lengths of jewelry wire, each approximately 24 inches long. Slide one wire through the bottom loop of the skull. Slide the other wire through the two side loops of the skull. Center the wires through the loops, so there is an equal amount of wire coming out from each side of the skull.
Add the following pattern to one side of the bottom wire:
Repeat this pattern on the other side of the strand.
Add the following pattern to one side of the top wire:
Repeat this pattern on the other side of the strand.
Slide a pinch bail over the last beads of both strands on one side of the necklace. Pinch the bail closed over the strands. Repeat on the other side of the necklace.
Add the following pattern to the bottom strand:
Add a crimp tube to the wire and loop the wire back through the crimp tube, leaving the loop long enough to be covered by three crimp covers. Crimp in place. Repeat this step on the other side of the necklace.
Add the following pattern to the top strand:
Add a crimp tube to the wire and loop the wire back through the crimp tube, leaving the loop long enough to be covered by two crimp covers. Crimp in place. Repeat this step on the other side of the necklace.
Slide the loop on one end of the short strand through the leather necklace, twisting the strand once around the necklace. Slide the loop down to create a swag or swoop in the strand to your liking. Once in place, secure with two crimp covers around the leather and glue. Allow to dry. Repeat on the other side of the necklace.
Slide the loop on one end of the long strand through the leather necklace, twisting the strand once around the necklace. Slide the loop down to create a swag or swoop to your liking. Once in place, secure with three crimp covers around the leather and glue. Allow to dry. Repeat on the other side of the necklace.