Create a beautiful necklace for spring!
Add a seed bead and a fire-polished bead to an eye pin. Make a simple loop at the top of the beads. Attach to the loop of a second eye pin.
Add a seed bead and a fire-polished bead to the second eye pin. Slide the lucite flower onto the eye pin, followed by a garnet bead, a pearl, and a seed bead. Make a wrapped loop at the top of the beads.
Add a garnet bead to an eye pin, followed by a fire-polished bead, a Golem Design Studio bead, a fire-polished bead, and a garnet bead. Make a simple loop at the top of the beads.
Attach the Golem Design Studio bead link to the flower dangle.
Attach a jump ring to each half of the toggle clasp.
Cut a length of jewelry wire approximately 22 inches long. Slide a crimp tube onto one end, followed by the jump ring attached to one half of the toggle clasp. Bring the wire back through the crimp tube and crimp in place.
Add the following pattern to the wire: a fire-polished bead, a garnet bead, a fire-polished bead, and a pearl. Repeat three times.
Add a fire-polished bead, a garnet bead, a dagger bead, a garnet bead, and a fire polished bead.
Add a pearl, then repeat the patteern from step 8. Add a garnet bead, a Golem Design Studio bead, and a garnet bead.
Add a fire-polished bead, a garnet bead, a dagger bead, a garnet bead, a fire-polished bead, and a pearl. Repeat this pattern once.
Add a fire-polished bead and the dangle focal. Make a mirror image of the entire pattern on the other side of the focal.
Add a crimp tube to the end of the wire, followed by the jump ring attached to the other half of the clasp. Bring the wire back through the crimp tube and crimp in place.
Note: Please make sure to double check our list of components with what's actually in stock on the supplies tab.
Nice choice! All or most of the products needed for this project are shown below with quantities. Sometimes we sell out of components and aren’t able to order more from the manufacturer (we know, it is very disappointing to us, too). Use the opportunity to mix up the design and make it yours by substituting similar products or altering the entire color scheme—it’s up to you!
Create a beautiful necklace for spring!
Add a seed bead and a fire-polished bead to an eye pin. Make a simple loop at the top of the beads. Attach to the loop of a second eye pin.
Add a seed bead and a fire-polished bead to the second eye pin. Slide the lucite flower onto the eye pin, followed by a garnet bead, a pearl, and a seed bead. Make a wrapped loop at the top of the beads.
Add a garnet bead to an eye pin, followed by a fire-polished bead, a Golem Design Studio bead, a fire-polished bead, and a garnet bead. Make a simple loop at the top of the beads.
Attach the Golem Design Studio bead link to the flower dangle.
Attach a jump ring to each half of the toggle clasp.
Cut a length of jewelry wire approximately 22 inches long. Slide a crimp tube onto one end, followed by the jump ring attached to one half of the toggle clasp. Bring the wire back through the crimp tube and crimp in place.
Add the following pattern to the wire: a fire-polished bead, a garnet bead, a fire-polished bead, and a pearl. Repeat three times.
Add a fire-polished bead, a garnet bead, a dagger bead, a garnet bead, and a fire polished bead.
Add a pearl, then repeat the patteern from step 8. Add a garnet bead, a Golem Design Studio bead, and a garnet bead.
Add a fire-polished bead, a garnet bead, a dagger bead, a garnet bead, a fire-polished bead, and a pearl. Repeat this pattern once.
Add a fire-polished bead and the dangle focal. Make a mirror image of the entire pattern on the other side of the focal.
Add a crimp tube to the end of the wire, followed by the jump ring attached to the other half of the clasp. Bring the wire back through the crimp tube and crimp in place.
Note: Please make sure to double check our list of components with what's actually in stock on the supplies tab.
