Bring beautiful bracelet strands together with Hiilos interchangeable clasps. You can even mix and match different strands together in different combinations to create all new styles every time you wear it.
Cut a length of hemp cord approximately 14 inches long. Fold the cord in half and bring through one ring of the gold-filled 15mm and 10mm interlocking rings. Pull the cord ends through the fold of the cord and pull tight around the ring. Repeat with another length of cord on the other ring. Trim the ends to the desired bracelet length, keeping in mind the clasp will add some length and that you need to knot the ends. Knot each end of cord.
Add a 6-inch length of chain to one side of the Nunn Design antique gold-plated pewter small hammered circle hoop using a jump ring. Repeat on the other side of the hoop. Attach a tiny seastart charm to the bottom of the hoop between the chains using a jump ring. Trim the ends of the chain on both sides of the strand equally to the desired length for a bracelet. Add a jump ring to one end. With the jump ring still open, add a TOHO seed bead to the jump ring. Close the jump ring and repeat on the other end of the strand.
Cut a length of jewelry wire approximately 12 inches long. Slide a crimp tube onto the end of the wire, followed by a seed bead. Bring the wire back through the crimp tube and crimp in place.
Add 2 Czech glass 3mm luster iris Capri blue melon beads to the wire, followed by this pattern:
Repeat this pattern twice, leaving off the last 3 melon beads. Slide a crimp tube onto the end of the wire, followed by a seed bead. Bring the wire back through the crimp tube and crimp in place.
Use pliers to gently open an 11mm tube for Hiilos interchangeable clasps. Add the knotted cords on one end of the strand to the tube by sliding the knots into the tube. Then, add the jump ring on one end of the chain strand. Then, add the seed bead at the end of the beaded strand. Close the ends of the tube and squeeze the tube shut. Repeat on the other end of the bracelet with another tube.
How to Finish Chain for a Hiilos Interchageable Clasp Video
How to Finish a Beaded Strand for a Hiilos Interchangeable Clasp Video
Slide the tube on end of the bracelet into one side of the HIilos 11mm clasp and then slide the tube on the other end of the bracelet into the other side of the clasp in reverse order.
Nice choice! All or most of the products needed for this project are shown below with quantities. Sometimes we sell out of components and aren’t able to order more from the manufacturer (we know, it is very disappointing to us, too). Use the opportunity to mix up the design and make it yours by substituting similar products or altering the entire color scheme—it’s up to you!
Bring beautiful bracelet strands together with Hiilos interchangeable clasps. You can even mix and match different strands together in different combinations to create all new styles every time you wear it.
Cut a length of hemp cord approximately 14 inches long. Fold the cord in half and bring through one ring of the gold-filled 15mm and 10mm interlocking rings. Pull the cord ends through the fold of the cord and pull tight around the ring. Repeat with another length of cord on the other ring. Trim the ends to the desired bracelet length, keeping in mind the clasp will add some length and that you need to knot the ends. Knot each end of cord.
Add a 6-inch length of chain to one side of the Nunn Design antique gold-plated pewter small hammered circle hoop using a jump ring. Repeat on the other side of the hoop. Attach a tiny seastart charm to the bottom of the hoop between the chains using a jump ring. Trim the ends of the chain on both sides of the strand equally to the desired length for a bracelet. Add a jump ring to one end. With the jump ring still open, add a TOHO seed bead to the jump ring. Close the jump ring and repeat on the other end of the strand.
Cut a length of jewelry wire approximately 12 inches long. Slide a crimp tube onto the end of the wire, followed by a seed bead. Bring the wire back through the crimp tube and crimp in place.
Add 2 Czech glass 3mm luster iris Capri blue melon beads to the wire, followed by this pattern:
Repeat this pattern twice, leaving off the last 3 melon beads. Slide a crimp tube onto the end of the wire, followed by a seed bead. Bring the wire back through the crimp tube and crimp in place.
Use pliers to gently open an 11mm tube for Hiilos interchangeable clasps. Add the knotted cords on one end of the strand to the tube by sliding the knots into the tube. Then, add the jump ring on one end of the chain strand. Then, add the seed bead at the end of the beaded strand. Close the ends of the tube and squeeze the tube shut. Repeat on the other end of the bracelet with another tube.
How to Finish Chain for a Hiilos Interchageable Clasp Video
How to Finish a Beaded Strand for a Hiilos Interchangeable Clasp Video
Slide the tube on end of the bracelet into one side of the HIilos 11mm clasp and then slide the tube on the other end of the bracelet into the other side of the clasp in reverse order.