Create a cute bracelet set filled with hearts and love!
Cut three strands of the pink variegated Amiet cord and two strands of the burgundy Amiet cord 18 inches long each, for a total of 5 strands.
Knot the ends of the cords together at each end of your bracelet to the size needed to fit over your hand. Trim each knot and secure with glue or a thread burner.
Secure the heart charm to the center of the bracelet using a separate burgundy cord and knotting the charm over all 5 strands. Make a second knot and then trim. Secure with glue or a thread burner.
Make a sliding knot closure over the two ends of the bracelet using the burgundy cord. Knot the tails of the closure cord close to the sliding knot and trim. Secure with glue or a thread burner.
Cut a length of pink variegated cord 18 inches longer than you need for a bracelet. Make a double knot in the cord, leaving an 8-inch tail.
Add a seed bead to the cord and make another double knot at the end of the seed bead. Repeat 10 times.
Double knot the cord at each end of your bracelet to the size needed to fit over your hand, leaving a 1-inch tail from the knot. Add a seed bead to each end and then make another double knot at the end of each seed bead. Trim each knot and secure with glue or a thread burner.
Make a sliding knot closure over the two ends of the bracelet using the same cord color. Leave each end of the closure cord long and double knot about an inch from each end. Add a seed bead to each end and double knot to secure the seed bead in place. Trim each knot and secure with glue or a thread burner.
Follow the instructions for the Diagonal Weave, using the pink variegated cord for all strands needed. Continue the weave for about 3 inches. And then knot the cords together.
Knot the ends of the cords together at each end of your bracelet to the size needed to fit over your hand. Trim each knot and secure with glue or a thread burner.
Make a sliding knot closure over the two ends of the bracelet using the same cord color. Knot the tails of the closure cord close to the sliding knot and trim. Secure with glue or a thread burner.
Cut a length of burgundy cord 18 inches long.
Bring the cord through one link at the end of a 1 ½-inch length of heart chain. Center the cord on the link and knot to secure. Double the knot.
Add a seed bead to the cords and double knot at the end of the seed bead.
Repeat steps 1-3 on the other side of the chain.
Double knot the cords at each end of your bracelet to the size needed to fit over your hand, leaving a 1-inch tail from the knot. Add a seed bead to each end and then make another double knot at the end of each seed bead. Trim each knot and secure with glue or a thread burner.
Make a sliding knot closure over the two ends of the bracelet using the same cord color. Leave each end of the closure cord long and double knot about an inch from each end. Add a seed bead to each end and double knot to secure the seed bead in place. Trim each knot and secure with glue or a thread burner.
Nice choice! All or most of the products needed for this project are shown below with quantities. Sometimes we sell out of components and aren’t able to order more from the manufacturer (we know, it is very disappointing to us, too). Use the opportunity to mix up the design and make it yours by substituting similar products or altering the entire color scheme—it’s up to you!
Create a cute bracelet set filled with hearts and love!
Cut three strands of the pink variegated Amiet cord and two strands of the burgundy Amiet cord 18 inches long each, for a total of 5 strands.
Knot the ends of the cords together at each end of your bracelet to the size needed to fit over your hand. Trim each knot and secure with glue or a thread burner.
Secure the heart charm to the center of the bracelet using a separate burgundy cord and knotting the charm over all 5 strands. Make a second knot and then trim. Secure with glue or a thread burner.
Make a sliding knot closure over the two ends of the bracelet using the burgundy cord. Knot the tails of the closure cord close to the sliding knot and trim. Secure with glue or a thread burner.
Cut a length of pink variegated cord 18 inches longer than you need for a bracelet. Make a double knot in the cord, leaving an 8-inch tail.
Add a seed bead to the cord and make another double knot at the end of the seed bead. Repeat 10 times.
Double knot the cord at each end of your bracelet to the size needed to fit over your hand, leaving a 1-inch tail from the knot. Add a seed bead to each end and then make another double knot at the end of each seed bead. Trim each knot and secure with glue or a thread burner.
Make a sliding knot closure over the two ends of the bracelet using the same cord color. Leave each end of the closure cord long and double knot about an inch from each end. Add a seed bead to each end and double knot to secure the seed bead in place. Trim each knot and secure with glue or a thread burner.
Follow the instructions for the Diagonal Weave, using the pink variegated cord for all strands needed. Continue the weave for about 3 inches. And then knot the cords together.
Knot the ends of the cords together at each end of your bracelet to the size needed to fit over your hand. Trim each knot and secure with glue or a thread burner.
Make a sliding knot closure over the two ends of the bracelet using the same cord color. Knot the tails of the closure cord close to the sliding knot and trim. Secure with glue or a thread burner.
Cut a length of burgundy cord 18 inches long.
Bring the cord through one link at the end of a 1 ½-inch length of heart chain. Center the cord on the link and knot to secure. Double the knot.
Add a seed bead to the cords and double knot at the end of the seed bead.
Repeat steps 1-3 on the other side of the chain.
Double knot the cords at each end of your bracelet to the size needed to fit over your hand, leaving a 1-inch tail from the knot. Add a seed bead to each end and then make another double knot at the end of each seed bead. Trim each knot and secure with glue or a thread burner.
Make a sliding knot closure over the two ends of the bracelet using the same cord color. Leave each end of the closure cord long and double knot about an inch from each end. Add a seed bead to each end and double knot to secure the seed bead in place. Trim each knot and secure with glue or a thread burner.