This bracelet mixes different metal tones with PRESTIGE Crystal. Please note that the metal finishes of the items in the supplies vary slightly from those pictured.
You can make this bracelet longer or shorter by adjusting the chain lengths and adding extra jump rings if needed. Place a small dab of E6000 glue into a bezel setting. Press a cushion stone into the glue and the setting. Do this for all three of your stones and settings. Let fully dry before moving onto the next step.
Precut your chain into 6 segments, 2 inches long each. Set aside for now.
Place a bicone bead onto a head pin and make a simple wire loop right after the bead. Trim excess wire. Repeat this step for all of your bicones, both the 4mm and 6mm size. You will end up with 24 dangles.
Time to build our bracelet from one end to the other! Please refer to the photo as needed. Open a 5mm jump ring and link onto it the lobster clasp and 3 lengths of cut chain. Close the jump ring.
Open a 7mm jump ring and link onto it the other sides of the cut chain that you already attached, four 4mm bicone dangles, two 6mm bicone dangles, and the side loop of one of your bezel settings. Close the jump ring.
Open another 7mm jump ring and link it to the loop on the other side of your bezel setting. Also link onto it four 4mm bicone dangles, two 6mm bicone dangles, and the side loop of another one of your bezel settings. Close the jump ring.
Repeat the previous step to attach your third bezel.
Open another 7mm jump ring and link it to the loop on the other side of your bezel setting. Also link onto it four 4mm bicone dangles, two 6mm bicone dangles, and the the end chain links to your remaining 3 cut lengths of chain. Close the jump ring.
Open a 5mm jump ring and link it to the other ends of the 3 chains that you just attached. Close the jump ring.
Nice choice! All or most of the products needed for this project are shown below with quantities. Sometimes we sell out of components and aren’t able to order more from the manufacturer (we know, it is very disappointing to us, too). Use the opportunity to mix up the design and make it yours by substituting similar products or altering the entire color scheme—it’s up to you!
This bracelet mixes different metal tones with PRESTIGE Crystal. Please note that the metal finishes of the items in the supplies vary slightly from those pictured.
You can make this bracelet longer or shorter by adjusting the chain lengths and adding extra jump rings if needed. Place a small dab of E6000 glue into a bezel setting. Press a cushion stone into the glue and the setting. Do this for all three of your stones and settings. Let fully dry before moving onto the next step.
Precut your chain into 6 segments, 2 inches long each. Set aside for now.
Place a bicone bead onto a head pin and make a simple wire loop right after the bead. Trim excess wire. Repeat this step for all of your bicones, both the 4mm and 6mm size. You will end up with 24 dangles.
Time to build our bracelet from one end to the other! Please refer to the photo as needed. Open a 5mm jump ring and link onto it the lobster clasp and 3 lengths of cut chain. Close the jump ring.
Open a 7mm jump ring and link onto it the other sides of the cut chain that you already attached, four 4mm bicone dangles, two 6mm bicone dangles, and the side loop of one of your bezel settings. Close the jump ring.
Open another 7mm jump ring and link it to the loop on the other side of your bezel setting. Also link onto it four 4mm bicone dangles, two 6mm bicone dangles, and the side loop of another one of your bezel settings. Close the jump ring.
Repeat the previous step to attach your third bezel.
Open another 7mm jump ring and link it to the loop on the other side of your bezel setting. Also link onto it four 4mm bicone dangles, two 6mm bicone dangles, and the the end chain links to your remaining 3 cut lengths of chain. Close the jump ring.
Open a 5mm jump ring and link it to the other ends of the 3 chains that you just attached. Close the jump ring.
