Emerald Cut Pendants make perfect bracelet dangles! Learn how to make this bracelet to start adding them as dangles to your designs.
Cut a length of Celtic chain to the length you need for a bracelet, keeping in mind, the clasp will add some length. We will be working from the center of the chain and out on both sides.
Add a Crystal Lilac Shadow bicone to a head pin, followed by a Dreamy Rose pearl. Make a wrapped loop at the top of the beads. Repeat once for a total of two dangles.
Add a Cyclamen Opal Shimmer 2x bicone to a head pin and make a wrapped loop at the top of the bead. Repeat 9 times for a total of 10 dangles.
Add a Crystal Lilac Shadow bicone to a head pin and make a wrapped loop at the top of the bead. Repeat 5 times for a total of 6 dangles.
Add a Dreamy Rose pearl to a head pin and make a wrapped loop at the top of the bead. Repeat 7 times for a total of 8 dangles.
Attach the 12mm Emerald Cut Pendant in Amethyst to the link at the center of the chain using a jump ring.
Attach a 9mm Emerald Cut Pendant in Light Amethyst to the next link over on one side of the bracelet using a jump ring. Repeat on the other side of the bracelet.
Add a Crystal Lilac Shadow dangle to a jump ring, followed by a Dreamy Rose pearl dangle, and a Cyclamen Opal Shimmer dangle. Attach the jump ring to the next link over on one side of the bracelet. Repeat on the other side of the bracelet.
Attach a 9mm Emerald Cut Pendant in Amethyst to the next link over on one side of the bracelet using a jump ring. Repeat on the other side of the bracelet.
Repeat Step 9.
Repeat Steps 8-11 for each side of the bracelet until you have used all of the dangles and Emerald cut pendants, except for two Dreamy Rose pearl dangles. Attach one of these dangles to the next link on each side of the bracelet using a jump ring for each.
Attach the loop component of the toggle clasp to one end of the bracelet using a jump ring. Attach the bar component using three jump rings linked together.
Nice choice! All or most of the products needed for this project are shown below with quantities. Sometimes we sell out of components and aren’t able to order more from the manufacturer (we know, it is very disappointing to us, too). Use the opportunity to mix up the design and make it yours by substituting similar products or altering the entire color scheme—it’s up to you!
Emerald Cut Pendants make perfect bracelet dangles! Learn how to make this bracelet to start adding them as dangles to your designs.
Cut a length of Celtic chain to the length you need for a bracelet, keeping in mind, the clasp will add some length. We will be working from the center of the chain and out on both sides.
Add a Crystal Lilac Shadow bicone to a head pin, followed by a Dreamy Rose pearl. Make a wrapped loop at the top of the beads. Repeat once for a total of two dangles.
Add a Cyclamen Opal Shimmer 2x bicone to a head pin and make a wrapped loop at the top of the bead. Repeat 9 times for a total of 10 dangles.
Add a Crystal Lilac Shadow bicone to a head pin and make a wrapped loop at the top of the bead. Repeat 5 times for a total of 6 dangles.
Add a Dreamy Rose pearl to a head pin and make a wrapped loop at the top of the bead. Repeat 7 times for a total of 8 dangles.
Attach the 12mm Emerald Cut Pendant in Amethyst to the link at the center of the chain using a jump ring.
Attach a 9mm Emerald Cut Pendant in Light Amethyst to the next link over on one side of the bracelet using a jump ring. Repeat on the other side of the bracelet.
Add a Crystal Lilac Shadow dangle to a jump ring, followed by a Dreamy Rose pearl dangle, and a Cyclamen Opal Shimmer dangle. Attach the jump ring to the next link over on one side of the bracelet. Repeat on the other side of the bracelet.
Attach a 9mm Emerald Cut Pendant in Amethyst to the next link over on one side of the bracelet using a jump ring. Repeat on the other side of the bracelet.
Repeat Step 9.
Repeat Steps 8-11 for each side of the bracelet until you have used all of the dangles and Emerald cut pendants, except for two Dreamy Rose pearl dangles. Attach one of these dangles to the next link on each side of the bracelet using a jump ring for each.
Attach the loop component of the toggle clasp to one end of the bracelet using a jump ring. Attach the bar component using three jump rings linked together.
