Anna Bronze pendants are perfect for matching jewelry sets!
For the necklace, cut a length of chain approximately 1 3/4 inches long. Add a crystal pendant to the end using a jump ring. Add a 4mm bicone to a head pin and attach it to the 3rd link in the chain from the top by making a wrapped loop. Add a jump ring to the top link of the chain.
Cut a length of chain approximately 1 1/2 inches long. Add a 4mm bicone to a head pin and attach it to the bottom of the chain by making a wrapped loop. Add this chain to the same jump ring at the top of your previous chain dangle.
Cut a length of chain 1-inch long. Add a 4mm bicone to a head pin and attach it to the bottom of the chain by making a wrapped loop. Add this chain to the same jump ring at the top of your previous chain dangles. Attach this jump ring to the bottom of the Anna Bronze two crescent moons focal.
Add a 6mm bicone to an eye pin and attach it to the inside loop of the focal by making a wrapped loop. Attach a crystal pendant to the bottom of the eye pin using a jump ring.
Cut a length of chain approximately 30 inches. Slide the chain through the bail of the focal. Attach the swivel hook clasp to one end of the chain.
For the earrings, cut a length of chain approximately 1 1/4 inches. Slide a 4mm Smoke Topaz bicone onto a head pin and attach to the end of the chain by making a wrapped loop. Attach a jump ring to the top of the chain.
Cut a length of chain approximately 1 3/4 inches long. Attach a crystal pendant to the bottom of the chain using a jump ring. Add a Smoke Topaz bicone onto a head pin and attach to the 6th link from the top by making a wrapped loop. Add a Crystal AB bicone to a head pin and add to the 3rd link from the top by making a wrapped loop. Attach this chain to the same jump ring at the top of the previous dangle.
Cut a length of chain approximately 1 inch long. Add a Smoke Topaz 4mm bicone to a head pin and attach to the center link by making a wrapped loop. Add both ends of this chain to the jump ring at the top of the previous dangle.
Attach the jump ring with all the dangles to the bottom of an Anna Bronze crescent moon.
Add a 6mm bicone to an eye pin and attach it to the top loop of the crescent moon by making a wrapped loop.
Add a 4mm Smoke Topaz bicone to one of the leftover oval links from the chain and attach to the eye of the eye pin.
Open the loop of an earwire and attach to the top of the crescent moon. Close the loop.
Repeat these steps to make the other earring.
Nice choice! All or most of the products needed for this project are shown below with quantities. Sometimes we sell out of components and aren’t able to order more from the manufacturer (we know, it is very disappointing to us, too). Use the opportunity to mix up the design and make it yours by substituting similar products or altering the entire color scheme—it’s up to you!
Anna Bronze pendants are perfect for matching jewelry sets!
For the necklace, cut a length of chain approximately 1 3/4 inches long. Add a crystal pendant to the end using a jump ring. Add a 4mm bicone to a head pin and attach it to the 3rd link in the chain from the top by making a wrapped loop. Add a jump ring to the top link of the chain.
Cut a length of chain approximately 1 1/2 inches long. Add a 4mm bicone to a head pin and attach it to the bottom of the chain by making a wrapped loop. Add this chain to the same jump ring at the top of your previous chain dangle.
Cut a length of chain 1-inch long. Add a 4mm bicone to a head pin and attach it to the bottom of the chain by making a wrapped loop. Add this chain to the same jump ring at the top of your previous chain dangles. Attach this jump ring to the bottom of the Anna Bronze two crescent moons focal.
Add a 6mm bicone to an eye pin and attach it to the inside loop of the focal by making a wrapped loop. Attach a crystal pendant to the bottom of the eye pin using a jump ring.
Cut a length of chain approximately 30 inches. Slide the chain through the bail of the focal. Attach the swivel hook clasp to one end of the chain.
For the earrings, cut a length of chain approximately 1 1/4 inches. Slide a 4mm Smoke Topaz bicone onto a head pin and attach to the end of the chain by making a wrapped loop. Attach a jump ring to the top of the chain.
Cut a length of chain approximately 1 3/4 inches long. Attach a crystal pendant to the bottom of the chain using a jump ring. Add a Smoke Topaz bicone onto a head pin and attach to the 6th link from the top by making a wrapped loop. Add a Crystal AB bicone to a head pin and add to the 3rd link from the top by making a wrapped loop. Attach this chain to the same jump ring at the top of the previous dangle.
Cut a length of chain approximately 1 inch long. Add a Smoke Topaz 4mm bicone to a head pin and attach to the center link by making a wrapped loop. Add both ends of this chain to the jump ring at the top of the previous dangle.
Attach the jump ring with all the dangles to the bottom of an Anna Bronze crescent moon.
Add a 6mm bicone to an eye pin and attach it to the top loop of the crescent moon by making a wrapped loop.
Add a 4mm Smoke Topaz bicone to one of the leftover oval links from the chain and attach to the eye of the eye pin.
Open the loop of an earwire and attach to the top of the crescent moon. Close the loop.
Repeat these steps to make the other earring.
