Watch Becky create these jewelry pieces in our Facebook Live Video.
For the earrings, add a 4mm honeydew bead to a head pin, followed by an 8/0 round turquoise bead, an 8/0 round red bead, a turquoise bead, a rose gold Demi Round, a honeydew bead, a rose gold Demi Round, a turquoise bead, a red bead, a turquoise bead, and a honeydew bead. Make a wrapped loop at the top of the bead.
Add a plumeria TOHO Treasure bead to an eye pin, followed by an 8/0 red seed bead, a rose gold Demi Round, an opaque dark beige luster seed bead, an Avocado bead, a dark beige bead, a rose gold Demi Round, a red seed bead, and a plumeria bead. Make a simple loop at the end of the beads.
Repeat step 1, but this time add the beads to an eye pin.
Open the loop on one end of your Avocado bead link and add the dangle you made in step 1. Close the loop. Open the loop on the other end of the Avocado bead link and add the bead link you made in step 3. Close the loop.
Open the loop of an earwire and attach it to the top of your earring. Close the loop.
Repeat steps 1-5 to make the other earring.
For the bracelet, cut a length of thread at least 3 feet long. Add a beading needle to each end of the thread. Add 11 beige luster beads to the center of the thread. Bring one needle through one of the stringing holes on a Triangle Bead. Bring the other needle through the other stringing hole of the same triangle bead. Pull close up to the seed beads to make a loop.
Add the following pattern to the thread:
Repeat this pattern 6 times, then add 1 prong bead on each thread and 1 Triangle Bead with a needle through each stringing hole.
Add 11 beige seed beads to one end of the thread. Then, bring the needle through the other Triangle bead stringing hole to make a loop.
Bring the thread back through the beads to reinforce your bracelet. Then secure and trim your thread ends.
Attach each half of the toggle clasp to each end of the bracelet using a jump ring for each.
Nice choice! All or most of the products needed for this project are shown below with quantities. Sometimes we sell out of components and aren’t able to order more from the manufacturer (we know, it is very disappointing to us, too). Use the opportunity to mix up the design and make it yours by substituting similar products or altering the entire color scheme—it’s up to you!
Watch Becky create these jewelry pieces in our Facebook Live Video.
For the earrings, add a 4mm honeydew bead to a head pin, followed by an 8/0 round turquoise bead, an 8/0 round red bead, a turquoise bead, a rose gold Demi Round, a honeydew bead, a rose gold Demi Round, a turquoise bead, a red bead, a turquoise bead, and a honeydew bead. Make a wrapped loop at the top of the bead.
Add a plumeria TOHO Treasure bead to an eye pin, followed by an 8/0 red seed bead, a rose gold Demi Round, an opaque dark beige luster seed bead, an Avocado bead, a dark beige bead, a rose gold Demi Round, a red seed bead, and a plumeria bead. Make a simple loop at the end of the beads.
Repeat step 1, but this time add the beads to an eye pin.
Open the loop on one end of your Avocado bead link and add the dangle you made in step 1. Close the loop. Open the loop on the other end of the Avocado bead link and add the bead link you made in step 3. Close the loop.
Open the loop of an earwire and attach it to the top of your earring. Close the loop.
Repeat steps 1-5 to make the other earring.
For the bracelet, cut a length of thread at least 3 feet long. Add a beading needle to each end of the thread. Add 11 beige luster beads to the center of the thread. Bring one needle through one of the stringing holes on a Triangle Bead. Bring the other needle through the other stringing hole of the same triangle bead. Pull close up to the seed beads to make a loop.
Add the following pattern to the thread:
Repeat this pattern 6 times, then add 1 prong bead on each thread and 1 Triangle Bead with a needle through each stringing hole.
Add 11 beige seed beads to one end of the thread. Then, bring the needle through the other Triangle bead stringing hole to make a loop.
Bring the thread back through the beads to reinforce your bracelet. Then secure and trim your thread ends.
Attach each half of the toggle clasp to each end of the bracelet using a jump ring for each.