Wedded Bliss

Bracelet

Link two 12mm navette sew-on rhinestones in Crystal back to back using a 5.5mm gunmetal-plated 21 gauge open jump ring on both ends of the stones. When linking navettes, only open the jump rings as wide as necessary; they will go through the both holes easier this way. Don't try to force them, as you could end up chipping or breaking the navette crystal. You may want to purchase extra jump rings and navettes just in case.

String a 8mm round pearl in Cream onto a 1.5-inch gunmetal-plated 22 gauge eye pin. Make a simple loop on the end of the eye pin. Connect the pearl link to the jump ring on the end of the connected navettes. Connect two more navettes as you did before and attach these connected navettes to the other side of the pearl link. Continue making navette links and pearl links and connecting them until your strand is the desired length. We alternated five navette links with four pearl links. Attach one end of the strand to the last hole on the TierraCast antique pewter 6 hole end bar using a 5.5mm jump ring. If you need your strand longer to fit your wrist, you can use 4.5mm gunmetal-plated 21 gauge open jump rings to add length between the strand and the bar. We used three 4.5mm jump rings. Repeat on the other end of the strand.

String a white pearl from the 6mm Crystal Pearl I Do Designer Blend onto an eye pin. Make a simple loop on the other end of the eye pin. Repeat 12 times and link them all together in a strand. Add a 4.5mm jump ring to the end of the strand and attach it to the next hole in the bar using a 5.5mm jump ring. Again, you may need to adjust the amount of jump rings depending on your wrist. Repeat on the other end of the strand.

String a silver pearl from the I Do Designer Blend onto an eye pin. Make a simple loop on the other end of the eye pin. Repeat seven times. Link three of the pearl links together in a strand, then add a 18mm owlet sew-on rhinestone crystal to the end using a 4.5mm jump ring. Add a pearl link to the other end of the owlet using a 4.5mm jump ring. Add another owlet to the strand, followed by a pearl link, another owlet stone and then a pearl link. Then, link two more pearl links to the strand. Attach one end of the strand to the third hole in the bar using a 5.5mm jump ring. Repeat for the other end of the strand.

Repeat step three for the fourth strand of your bracelet using cream pearls this time and attach each end to the fourth hole in the bars.

Repeat steps one and two for the fifth strand of your bracelet, only this time use 8mm round pearls in White. Attach each end to the fifth hole in the bars.

Repeat step three for the sixth strand of your bracelet using silver pearls this time and attach each end to the sixth open hole in the bars.

Attach a gunmetal-plated 12x6.5mm trigger clasp to the bar on one end of the bracelet using a 4.5mm jump ring. Link eight 4.5mm jump rings together in a strand and attach the chain of jump rings to the bar on the other end of the bracelet. You can make this extender chain as long or as short as you need to accommodate for your wrist. String a 3mm Lochrose sew-on stone in Crystal onto a 1.5-inch gunmetal-plated 23 gauge head pin, followed by an 8mm Cream pearl and another Lochrose stone. Attach it to the end of your extender chain by creating a wrapped loop. ,

Owlet Earrings

String a Lochrose stone onto a head pin, followed by an 8mm Cream pearl and another Lochrose stone. Make a wrapped loop at the top of the head pin. Attach this dangle to an owlet stone using a 4.5mm jump ring.

Attach a gunmetal-plated earwire to the top stringing hole of the owlet stone using a 4.5mm jump ring. Repeat steps nine and ten for the other earring. ,

Navette Earrings

Link two navettes together back to back using a 5.5mm jump ring on both ends. Attach an earwire to the jump ring on one end using a 4.5mm jump ring.

String a Lochrose stone onto a head pin, followed by a 6mm cream pearl and another Lochrose stone. Attach this dangle to the jump ring on the bottom of the linked navettes by creating a wrapped loop. Repeat steps eleven and twelve for the other earring.

List of Components:
5810 6mm Crystal Pearl I Do Designer Blend (ADB0201, qty 1)
5810 8mm Round Pearl White (5810-WHITE8, qty 4)
5810 8mm Round Pearl Cream (5810-CRM8, qty 7)
3223 12mm Navette Sew-on Rhinestone Crystal (3223-CRY12, qty 24)
3231 18mm Owlet Sew-on Rhinestone Crystal (Unfoiled) (3231-CRYUF18, qty 5)
3188 3mm Lochrose Sew-On Stone Crystal (3188-CRY3, qty 10)
TierraCast Antique Pewter 6 Hole End Bar (PA-3169, qty 2)
Gunmetal-Plated 12x6.5mm Trigger Clasp (BGM-CL03, qty 1)
4.5mm Gunmetal-Plated 21 Gauge Open Jump Ring (BGM-OJR04-A, qty 40)
5.5mm Gunmetal-Plated 21 Gauge Open Jump Ring (BGM-OJR06-A, qty 36)
1.5-Inch Gunmetal-Plated 22 Gauge Eye Pin (100pc Pack) (FIND-1705, qty 1)
1.5-inch Gunmetal-Plated 23 Gauge Head Pin (BGM-HP15-24, qty 5)
Gunmetal-Plated Plain Earwire (BGM-EAR03, qty 4)